• Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 9:00 p.m. 10/21/2017 to 10:00 a.m. (EDT) 10/22/2017. We apologize for the inconvenience.
  • There are issues downloading CAD models for Press and Mold components from 2017/10/11. We are sorry for the inconvenience, and we are working to have this restored as quickly as possible. For details, please check here.

STM24 Integrated Stepper Motor

Part Number

Configured Part Number is shown.

STM24 Integrated Stepper Motor:Related Image
・Materials
Integrated Stepper Motors
STM integrated drive+motors fuse step motor and drive components into a single
device. These integrated steppers offer a space-saving design that reduces wiring
and saves on cost over separate motor and drive components. STM integrated
steppers,

Product Featutes
Sophisticated current control
Anti-resonance
Torque ripple smoothing
Microstep emulation
NEMA 24 frame size
Available Built-in incremental encoder

Buit in Circuit Protection
Short Circuit
Over Voltage
Under Voltage
Over Temp

Step Resolution
Full
Half
Microstepping
Microstep Emulation
The STM24x-3 integrated stepper is a drive+motor unit, fusing a NEMA 24 step motor and a sophisticated 6.0 A/phase (peak-of-sine) stepper
drive into a single device. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. See Related and
Recommended Products below for compatible 24 and 48 volt DC popwer supplies.
The STM24C-3Cx integrated stepper is designed to operate on a CANopen communication network and conforms to Can in Automation (CiA)
DS301 and DSP402 specifications. It supports Profile Position, Profile Velocity, and Homing modes, as well as the ability to run stored Q programs
via Applied Motion-specific CANopen objects.
The STM24SF-2Ax integrated stepper can operate in the following control modes: step (pulse) & direction, velocity (oscillator), streaming serial
commands . (STM24 integrated steppers do not support stored-program operation with the Applied Motion 4-axis and 8-axis SiNet Hubs).
The STM24QF-3x integrated stepper can operate in all of the same control modes as the SF option, plus the ability to run a Q program stored
in non-volatile memory. Q programs are created using Applied Motion’s Q Programmer™ software, which provides powerful commands for
motion, I/O, conditional processing, multi-tasking, math functions, and more. All STM23 units are setup and configured using Applied Motion’s
ST Configurator™ software.

On units ordered with and encoder. An integral 1000-line (4000 count/rev) incremental encoder is housed inside the same enclosure as the
drive electronics, providing protection from dust and debris. The integration of the encoder means the STM24x-3xE can perform special
functions not available otherwise. Stall Detection notifies the system as soon as the required torque is too great for the motor, which results in
a loss of synchronization between the rotor and stator, also known as stalling. Stall Prevention actually prevents stalling of the step motor by
dynamically adjusting motor speed to maintain synchronization of the rotor to the stator under all conditions. This unique feature allows step
motors to operate in a much broader range of applications than previously available to step motors, such as torque-control applications. The Stall
Prevention feature also performs static position maintenance, which maintains the position of the motor shaft when at rest.
Each STM24 integrated stepper comes with 3 digital inputs, 1 digital output, and 1 analog input. The digital inputs accept signals of 5-24 VDC
and can be used for connecting pulse & direction signals, end-of-travel limit switches, jog switches, quadrature encoder signals, PLC outputs,
sensors, or many other signal types. The digital output can be connected to PLC inputs, counters, lights, relays, or other devices. The analog input
accepts 0-5 VDC signals and can be used for velocity and position control.
The STM24x-3Ax comes with an RS-232 port for programming and serial communications. The STM24x-3Rx comes with an RS-485 port for
programming and serial communications.

Specifications

Part Number - Control - Com. Port - Encoder
STM24 - -QF - -3A - N
NEMA 24 Motor with Q prorramming , RS-232, No Encoder
Part Number
Motor
Series
Control
Mode
Communication
Ports
Encoder
STM24x-3 C -3C E
N
QF
SF
-3A
-3R

CANopen Only Control Modes Encoder
C QF SF E N
CANopen Q Programming
Streaming Commands
Analog Positioning
Encoder Following
Step & Direction
Velocity
(Oscillator)
Streaming Commands
Yes No

CANopen Only Communication Ports
-3C
-3A
-3R
RS-232
CANopen
RS-232 RS-485

Specifications
Digital Inputs 3
Digital Outputs 1
Analog Inputs 1 Single-ended
Status LEDs 1 Red, 1 Green
Holding Torque 204.09 N-cm
Step Angle 1.8 deg.
Rotor Inertia 8.97E-3 N-cm-sec²
Length 125.5 mm
Weight 1587.6 g
Operating Temp. 85° C
Insulation Class Class B (130° C)
Input Voltage 12 - 48 VDC
Part Number
STM24C-3CE
STM24C-3CN
STM24QF-3AE
STM24QF-3AN
STM24QF-3RE
STM24QF-3RN
STM24SF-3AE
STM24SF-3AN
STM24SF-3RE
STM24SF-3RN
Part NumberVolume DiscountDays to Ship Programming Communication Ports Closed Loop Feedback

9 Days

CAN OpenCAN-BusYes

9 Days

CAN OpenCAN-BusNo
Available

10 Days

Q-Programmer SoftwareSerial RS232Yes
Available

10 Days

Q-Programmer SoftwareSerial RS232No

9 Days

Q-Programmer SoftwareSerial RS485Yes

9 Days

Q-Programmer SoftwareSerial RS485No
Available

10 Days

StreamingSerial RS232Yes
Available

10 Days

StreamingSerial RS232No

9 Days

StreamingSerial RS485Yes

9 Days

StreamingSerial RS485No

Loading...

  1. 1

Lead Time

STM24 Integrated Stepper Motor:Related Image

More Information

STM24 Hardware Manual

 

For questions regarding software options, please contact Misumi engineering.

 

STM24 Integrated Stepper Motor:Related Image

Example

Basic Information

Category Integrated Motor Voltage Specifications DC Holding torque(N·m) 2.4
Frame Size NEMA 24 Step angle(°) 1.8 Reduction Gear No

Additional Products in this Category

Complementary Products

Tech Support