Dial Gauges

• 

  Dial Gauge - Absolute Digimatic Indicator, Standard Plunger Type, Series 543, ID-CX

  MITUTOYO

  [SPECIFICATIONS]
  • Display: 6-digit LCD, sign
  • Contact point: Spherical tip SR = 1.5mm (carbide tipped), part No. 901312 (for ISO/JIS Type) part No. 21BZB005 (for ANSI/AGD Type)
  • Spindle orientation for measurement: - Standard model that has a 12.7mm measuring range: No restrictions
  - Standard model that has a 25.4mm or 50.8mm measuring range: Normally at any position between the spindle pointing vertically downward to the spindle horizontal. To perform measurement with the spindle pointing above the horizontal requires a reverse-position coil spring (special accessory)
  • Position detection method: Capacitance type absolute linear encoder
  • Battery: SR44 (silver oxide button cell) × 1, part No. 938882
  • Battery life: Approximately 7,000 hours of continuous use
  • Maximum response speed: Not restricted (except for scanning measurement)
  • Service temperature range: 0 to 40°C
  • Storage temperature range: 0 to 60°C

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Series 543, ID-CX, Inch

  MITUTOYO

  • The ABS (absolute) sensor restores the last origin position automatically when the indicator is turned on.
  • Thanks to Mitutoyo's ABSOLUTE Linear Encoder, reliability has been increased due to elimination of over speed errors.
  • Tolerance-judging measurement is available by setting upper and lower limit values.
  • Battery life of approx. 7,000 hours in continuous use has been achieved with only one battery.
  • Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems.

  • Volume Discount is available

  Configure Now

  Ships as soon as	6 Days

• 

  Dial Gauge - Horizontal Lever Type, Dial Display, Series 513

  MITUTOYO

  • Provides easy access to shrouded surfaces that cannot be reached with conventional dial indicators.
  • No-clutch structure for automatic reversal of measuring direction.
  • Resistant to water and dust thanks to the onepiece bezel and O-ring seal for the crystal.
  • The glare-free flat crystal face has a scratch-resistant coating.
  • High sensitivity and quick response due to low-friction jeweled bearings.

  • Volume Discount is available

  Configure Now

  Ships as soon as	6 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Series 543, ID-SX

  MITUTOYO

  [Features]
  · Origin Setting (Zero Setting) Function / Direction Switching Function / Data Output Function / Error Warning Display

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Series 543, ID-S

  MITUTOYO

  • Cost-effective oriented design
  ID-SX indicators use a button-type battery (SR44) and come with the minimum of functionality for ease of use. There is a choice of models in the lineup allowing selection of 0.01 mm, 0.001 mm or inch-based measurement resolutions.
  • IP53 dust/water protection level
  The models listed below also provide IP53 dust/water protection level specifications: 543 794/94B/95/95B/96/96B
  • ABS (absolute) sensor
  These Digimatic indicators employ Mitutoyo’s proprietary ABS (absolute) sensor, which makes it possible to restore the origin point even if the power is turned off. This eliminates the need to perform origin restoration each time the power is turned on. Furthermore, this sensor ensures that overspeed errors do not occur, which improves reliability.
  • Long battery life
  One button battery (SR44) provides approximately 20,000 hours of continuous use for .0005”/0.01mm resolution models.

  • Volume Discount is available

  Configure Now

  Ships as soon as	6 Days

• 

  Dial Gauge - Absolute Digimatic Scale Units, Series 572

  MITUTOYO

  • SD series facilitates mounting on jigs, tools, and small machine tools to enable accurate positioning.
  • Built-in absolute scale including the ABS point requires no zero-set every time the power is turned on. In addition, reliability has improved thanks to elimination of overspeed errors.
  • Horizontal or vertical display according to the scale mounting direction.
  • The dust resistance and the environmental resistance of the display has improved. The SD-G series offers dust/water protection level IP66.
  • Long battery life for easier maintenance.
  • EC counters are available as external display units.
  • Equipped with an output port to transfer measurement data. This allows implementation in control systems and gaging systems.

  Configure Now

  Ships as soon as	8 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Series 575/ID-U, (ID-U1025)

  MITUTOYO

  This is a slim type of digital indicator with a 25 mm range.
  The ABSOLUTE Digimatic Indicator ID-U offers you the following benefits:
  The ABSOLUTE sensor means you don‘t have to carry out origin setting every time you power it on, saving you time and hassle.
  Its compact design makes it ideal for installing into measuring fixtures.
  Exceptional battery life.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Swivel Clamp, Accessory

  MITUTOYO

  [Features]
  · An accessory for the pocket type test indicator.
  · For ø6mm stem, ø8mm stem, and dovetail

  Configure Now

  Ships as soon as	Same Day

  Stock Items Included

• 

  Dial Gauge - Various Contact Points, Series 513

  MITUTOYO

  [Features]
  · An accessory (gauge head) for dial gauge.
  Optional Contact Points, Pocket Type

  Configure Now

  Ships as soon as	Same Day

  Stock Items Included

• 

  Dial Gauge - Thickness Type, Digital Display, Series 547, 7, ID-S

  MITUTOYO

  • Dial thickness gages can quickly measure the thickness of thin products such as paper and felt.
  • Contact point and anvil are both made of ceramic: rust-free.
  • Integrated molding of the bezel and crystal ensures protection against water and oil penetration via the front face.

  Configure Now

  Ships as soon as	8 Days

• 

  Dial Gauge - Horizontal Lever Type, Long Contact Point, Series 513

  MITUTOYO

  Range: 1.0mm
  Graduation: 0.01mm
  Accuracy: 10µm
  Measuring Force: 0.2N or less
  Dial Color: Yellow

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Standard Plunger Type, Dial Display

  MITUTOYO

  Dial Indicators Series 2- Metric Standard Type
  Series 2
  [FEATURES]
  Series 2 dial indicators are Mitutoyo’s most popular, and have the widest application.
  Standard 0.01mm graduation dial gauges having an outer frame with an outside diameter of 57mm. All types come with limit pins and an outer frame clamp as standard.
  The outer clamp and lifting lever (optional) can be attached to either the right or left side. These parts can be easily installed and removed without tools.
  Secured adhesion between the outer frame and crystal as well as the use of an O-ring ensure countermeasures against water and oil permeation via the front face.
  The stem spindle is made of high-strength quench-hardened stainless steel which resists strenuous use.
  A carbide contact point is used.
  The grand gear uses stainless steel that is resistant to wear and deformation.
  Application of a hard coating on the surface of the crystal makes the gauge highly scratch- and chemical-resistant.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Series 543, Inch/Metric, ID-SX

  MITUTOYO

  • Cost-effective oriented design ID-SX indicators use a button-type battery
  (SR44) and come with the minimum of functionality for ease of use.
  There is a choice of models in the lineup allowing selection of 0.01 mm,
  0.001 mm or inch-based measurement resolutions.
  • IP53 dust/water protection level The models listed below also provide IP53 dust/
  water protection level specifications: 543-794/94B/95/95B/96/96B
  • ABS (absolute) sensor These Digimatic indicators employ Mitutoyo’s proprietary
  ABS (absolute) sensor, which makes it possible to restore the origin point even
  if the power is turned off. This eliminates the need to perform origin restoration
  each time the power is turned on. Furthermore, this sensor ensures that overspeed
  errors do not occur, which improves reliability.
  • Long battery life One button battery (SR44) provides approximately 20,000 hours of continuous
  use for .0005”/0.01mm resolution models.

  Configure Now

  Ships as soon as	8 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Back-lit LCD, Series 543, ID-F

  MITUTOYO

  • GO/±NG judgment function: If a judgment result shows an out of tolerance condition, the display backlighting changes from green to red.
  • An analog bar indicator has been integrated to make upper/lower limit and turnover point reading more comfortable.
  • With Mitutoyo's ABSOLUTE Linear Encoder technology, once the measurement reference point has been set it will not be lost when the power is turned off. Also, reliability has been increased due to the elimination of over-speed errors.
  • Easy-to-read large LCD readout with the character height of 8.5mm.
  • External power supply type: battery change is not necessary. Power can also be supplied via the AC adapter supplied as a standard accessory.
  • The resolution can be switched between 0.001mm /0.01mm (or .001” /.0005” /.0001” /.00005”).
  • Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems.

  Configure Now

  Ships as soon as	10 Days

• 

  Dial Gauge - Compact Plunger Type, Dial Display, Series 1, Metric

  MITUTOYO

  It is ideal for use in applications where space is limited.
  Green limit markers are a standard accessory.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Coolant-Proof, Series 543, ID-N/B

  MITUTOYO

  Absolute LCD Digimatic Indicator ID-N, IP66, M2.5X0.45 Thread, 8mm Stem Diameter, 0-5mm Range, 0.01mm Graduation, +/-0.003mm Accuracy

  Configure Now

  Ships as soon as	Same Day

  Stock Items Included

• 

  Dial Gauge - Comparator Stand, Series 215, BS

  MITUTOYO

  Comparator Stand Series 215
  [FEATURES]
  Comparator Stands have a very stable, cast iron which enables precise measurement.
  The partially serrated anvil prevents very flat work pieces from wringing to it and the 2.3µm flatness (or better) promotes accurate measurement.
  The215-505-10model has a threaded column which enables easy and precise coarse adjustment.
  Serrated anvils 110x110mm are supplied With 215-405-10, and 150x150mm with 215-505-10 models.
  

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Dial Comparator

  MAHR

  • Use: Standard Type
  • Display Method: Dial
  • Maximum Measuring Length (Adjustment Range) (mm): 0 ~ 1
  • Scale Model: Balance scale
  • Mounting Shaft diameter (mm): 8

  Configure Now

  Ships as soon as	4 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Peak Hold Type, Flat Back, Series 543, ID-C, Metric

  MITUTOYO

  [Features]
  · Equipped with a peak detection function. In addition, pass/fail judgment can be made for this peak value.
  · Five buttons, status icons and key assist display allow various functions to be easily operated.
  · Equipped with a wide LCD and analog bar display.
  · ABS (absolute) method with absolute origin makes it unnecessary to set the origin every time the power is turned on. Also, since over-speed errors will not occur, reliability has also been improved.
  · The parameter setup kit (option) and dedicated software enable the use of various functions and parameter setting on a PC.
  It comes with a measurement data output terminal, enabling the configuration of statistical process management systems and measurement systems.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Linear Type, Digimatic Output, LGS-1012P

  MITUTOYO

  [Features]
  · Equipped with an electrostatic capacitance absolute encoder with origin which does not change even when the power is turned off.
  · Achieves high dust-proof and waterproof performance of IP66, suitable for field environments.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Compact Plunger Type, Dial Display

  TECLOCK

  [Features]
  · Small, lightweight, and easy to use with a high level of precision, it is widely used as a measurement instrument for measuring length in a variety of fields.
  [Applications]
  · For use in areas with limited space, such as sizing of machinery and assembly into dedicated machines.

  Configure Now

  Ships as soon as	4 Days

• 

  Dial Gauge - Lever Type, Non-Magnetic/Non-Electrifying, U Series

  OZAKISEISAKUJO

  • Use: Lever Type (Indicator)
  • Display Method: Dial
  • Maximum Measuring Length (Adjustment Range) (mm): 0 ~ 1
  • Scale Model: Balance scale
  • Feature: Because the probe and pointer are nonmagnetic, they are not easily affected by magnetic environments. The use of ceramic stems achieves non-conductivity, which allows them to be used in electric discharge machines, etc. The pale blue scale

  Configure Now

  Ships as soon as	4 Days

• 

  Dial Gauge - Digital Plunger Type, High-Accuracy, ID-H

  MITUTOYO

  1.2 In/30.4mm, .00002 In/.00005 In/.0001 In/0.0005mm/0.001mm, ID-H ABSOLUTE Digimatic Indicator, 3/8 In stem, Flat Back, With SPC/RS232 Data Output, With Analog Display, Back-Lit, ANSI

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Test Indicator - Pocket Type, Series 513

  MITUTOYO

  【Product Specifications】
  ・Jeweled bearings ensure high sensitivity and accuracy.
  ・Reversible measuring direction.
  ・Two holding bars are supplied. (Full sets only.)
  ・Fully adjustable bezel/dial face.
  ・Bezel is sealed with on O-ring to keep out water / oil.

  Configure Now

  Ships as soon as	32 Days

• 

  Dial Gauge - Absolute Solar Digimatic Indicator, Series 543, ID-SS

  MITUTOYO

  This solar-powered, standard model is environmentally friendly and very easy to use.
  The ABSOLUTE Digimatic Solar Indicator ID-SS offers you the following benefits:
  The ABSOLUTE sensor means you don‘t have to carry out origin setting every time you power it on, saving you time and hassle.
  There‘s no battery to change.
  The solar cell is operates from just 40 Lux.
  Super-capacitor charge storage enables you to work in low-level lighting conditions of less than 40 Lux.
  You can access all functions by using the large, user-friendly buttons on the front of the indicator.
  Large character height of 9 mm provides good readability.
  

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Granite Comparator Stand, Series 215, 150 x 200 x 50mm Base

  MITUTOYO

  Comparator Stand Series 215
  [FEATURES]
  Comparator Stands have a very stable, cast iron which enables precise measurement.
  The partially serrated anvil prevents very flat work pieces from wringing to it and the 2.3µm flatness (or better) promotes accurate measurement.
  The215-505-10model has a threaded column which enables easy and precise coarse adjustment.
  Serrated anvils 110x110mm are supplied With 215-405-10, and 150x150mm with 215-505-10 models.
  

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Peak Hold Type, Series 543, ID-C112AX

  MITUTOYO

  [Features]
  · Equipped with a peak detection function. In addition, pass/fail judgment can be made for this peak value.
  · Five buttons, status icons and key assist display allow various functions to be easily operated.
  · Equipped with a wide LCD and analog bar display.
  · ABS (absolute) method with absolute origin makes it unnecessary to set the origin every time the power is turned on. Also, since over-speed errors will not occur, reliability has also been improved.
  · The parameter setup kit (option) and dedicated software enable the use of various functions and parameter setting on a PC.
  It comes with a measurement data output terminal, enabling the configuration of statistical process management systems and measurement systems.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Various Lever Types, Dial Display, Series 513, Various Sets

  MITUTOYO

  • Specially designed for easy viewing of dial.
  • The dial face obliquely faces upward, allowing users to read the graduations from the user's side. It is convenient when probing on the side of a large workpiece and the workbench is high.
  • Using the universal holder allows easy hole centering. The dial face always faces upward when the indicator is rotated, which makes reading easy.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Standard Plunger Type, Long Range, Dial Display, Series 2

  MITUTOYO

  Dial Indicators
  SERIES 2 — Metric Standard Type
  Series 2 dial indicators are Mitutoyo’s most popular and have the widest application.
  [FEATURES]
  • Standard 0.01mm graduation dial gages having an outer frame with an outsidediameter of 57mm. All types come with limit pins and an outer-frame clamp asstandard.
  • The outer clamp and lifting lever (optional) can be attached to either the right or leftside. These parts can be easily installed and removed without tools.
  • Secured adhesion between the outer frame and crystal, as well as the use of an O-ring, protect against water and oil permeation via the front face.
  • The stem spindle is made of high-strength quench-hardened stainless steel forlongevity.
  •A carbide contact point is used.
  • The grand gear uses stainless steel that is resistant to wear and deformation.
  •Application of a hard coating on the surface of the crystal makes the gagehighly scratch- and chemical-resistant.
  [Specification]
  ●Minimum Display(mm):0.010
  ●Graduation Specification:0-100
  ●Mount Shaft Diameter (mm):8
  ●Dial diameter: 57mm
  

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Lever Type, Dial Display

  MAHR

  [Features]
  · Fixing bracket (shank) removable structure allows the position to be freely changed.
  · Wear-resistant artificial gems are used for the entire internal shaft.
  · There are 2 mounting shafts, 6 mm and 8 mm, which can be removed.
  · Vibration-proof structure.
  · A structure in which the pointer's cover glass can be removed, eliminating time spent repairing any damage to the glass.
  · Fixing bracket (shank) removable structure enables work that originally required multiple units to be done with a single unit, making it highly economical.
  [Applications]
  · General molding industry.
  · Research and development work.

  Configure Now

  Ships as soon as	4 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Signal Output Function, Series 543, ID-C112JX

  MITUTOYO

  [Features]
  · A measuring device that outputs the pass/fail judgment results of the detected position data. Unlike the mechanical type electric contact method, there is no contact degradation.
  · The output can be directly connected to an external device (PLC, etc.). (Output logic reversal is also possible.) The judgment results are displayed on the LCD display and 2-color LED.
  · This measuring device is equipped with a peak detection function and is also capable of pass/fail judgment on peak value and amplitude.
  · ABS (absolute) method with absolute origin is used for position detection, which eliminates the need for origin setting every time the power is turned on as well as the risk of over-speed errors.
  · 4 m cable included
  · Supports 5 to 24 VDC external power supply
  · Protection grade of IP54 (dust protection, splash-proof type)

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Calculation Type, Series 543, ID-C

  MITUTOYO

  • Calculation function operates on spindle displacement.
  • Entering the appropriate formula factors for a fixture dedicated to the application enables direct measurement readout, thereby eliminating any need for the conversion tables previously needed for those applications where fixtures are typically used.
  • Peak-Value Run-out/MAX/MIN Hold enables GO/±NG judgement for peak value.
  • Simple operation of many functions with five buttons and status icons.
  • Wide LCD and new analog bar graph are now standard on all models.
  • Sampling can be performed fifty times per second for accurate detection of maximum, minimum and run-out values.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Flat Back, Series 543, 543-470B

  MITUTOYO

  [SPECIFICATIONS]
  • Display: 6-digit LCD, sign
  • Contact point: Spherical tip SR = 1.5mm (carbide tipped), part No. 901312 (for ISO/JIS Type) part No. 21BZB005 (for ANSI/AGD Type)
  • Spindle orientation for measurement: - Standard model that has a 12.7mm measuring range: No restrictions
  - Standard model that has a 25.4mm or 50.8mm measuring range: Normally at any position between the spindle pointing vertically downward to the spindle horizontal. To perform measurement with the spindle pointing above the horizontal requires a reverse-position coil spring (special accessory)
  • Position detection method: Capacitance type absolute linear encoder
  • Battery: SR44 (silver oxide button cell) × 1, part No. 938882
  • Battery life: Approximately 7,000 hours of continuous use
  • Maximum response speed: Not restricted (except for scanning measurement)
  • Service temperature range: 0 to 40°C
  • Storage temperature range: 0 to 60°C

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Linear Type, Digimatic Output, Series 575

  MITUTOYO

  [Features]
  · Equipped with an electrostatic capacitance absolute encoder with origin which does not change even when the power is turned off.
  · Achieves high dust-proof and waterproof performance of IP66, suitable for field environments.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Compact Plunger Type, Dial Display

  OZAKISEISAKUJO

  • Use: Standard Type
  • Display Method: Dial
  • Feature: It is a compact type dial gauge with small surface diameter. Does not require space for multipoint measurement and mounting to a jig, etc.
  • Dimension J (mm): 8.0 0-0.03
  • Repeat Precision: 5

  Configure Now

  Ships as soon as	Same Day

  Stock Items Included

• 

  Dial Gauge - Compact Horizontal Lever Type, Dial Display【1-2 Pieces Per Package】

  MITUTOYO

  [Features]
  · Standard model.
  · Improved visibility
  · Easy to read cover plate
  · Prevents dust from entering the interior of the scale plate
  · The bezel and cover plate are integrated
  · The bezel is prevented from coming off
  · Multilayer coating is provided on the cover plate
  · Prevents the holding part of the stylus from rattling
  · Prevents the sensitivity and followability of the stylus from deteriorating
  · Inspection report included
  · Displays the length of the stylus on the scale board
  · Limit pointer can be mounted
  · Equipped with φ6 stem with dovetail groove as standard
  · Complies with the new JIS B7533:2015

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Extension Rods for Indicators

  MITUTOYO

  [Features]
  · An option for dial gauges.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Knife Edge Contact Point

  OZAKISEISAKUJO

  • Use: Measurement Element
  • Dimension: See the catalog
  • Material: SKS 3

  Configure Now

  Ships as soon as	4 Days

• 

  Dial Gauge - Stand, Granite Base, Series 215

  MITUTOYO

  This gauge stand with granite base offers you the following benefits:
  The base is made of granite that stays free of burrs due to its fine grain composition and the base will stay free of corrosion
  Column Ø: 30 mm
  Max. measurement height : 120 mm
  Fine adjustment: 1 mm
  Fine adjustment: 1 mm
  Stem hole ø: ø 3/8" / 9.53 mm , 8 mm with bush (standard accessory) mm
  Table flatness: 3 µm
  Perpendicularity table-stem hole: 0.2/100 mm/mm

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Absolute Digimatic Indicator, Slim, Series 575, ID-U

  MITUTOYO

  • General purpose indicator with the measuring range of 25.4mm/ 1”.
  • Cost-effective and user-friendly type which is equipped with the basic functions necessary.
  • The ABS (absolute) sensor restores the last origin position automatically when the indicator is turned on, and realizes high reliability by eliminating over-speed errors.
  • Battery life of 20,000 hours in continuous use has been achieved.
  • Easy-to-read large LCD readout with the character height of 8mm.
  • Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Test Indicator Centering Holder

  MITUTOYO

  Centering Holder
  •Allows large diameter cylinders or holes to be centered.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Flat Point Contact Point, Steel

  MITUTOYO

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Flat Point Contact Point

  MITUTOYO

  Optional Accessory for Digimatic and Dial Indicators and Linear Gages

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Compact Plunger Type, Flat Back, Series 1

  MITUTOYO

  [Features]
  · Compact-design dial indicator. Will not take up much space, even when installed onto jigs.
  [Applications]
  · For comparative measurements. For mounting on jigs, etc.

  Configure Now

  Ships as soon as	12 Days

• 

  Dial Gauge - Scale Dial Indicator, High Precision

  TECLOCK

  [Features]
  · High-precision dial gauge that can be read in units of 0.1 mm.
  [Applications]
  · For use in areas with limited space, such as sizing of machinery and assembly into dedicated machines.
  · Used for rough dimension measurement of woodwork and rubber material and judgment of deviation in dimensions.

  Configure Now

  Ships as soon as	4 Days

Loading...